Method 1: Reboot the wireless router
1. This is the simplest method but can be highly effective in most cases. Switch off the wireless router, leave it off for at least 60 seconds and then turn it back on again.
2. Try connecting to your wireless network.
Method 2: Perform Diagnostic Repair
1. Navigate to “Start -> Control Panel -> Network and Internet -> Network and Sharing Centre”.
2. Click on “Change Adapter Settings”.
3. Right click on your Wireless Network adapter and select “Diagnose”.
4. Diagnostic repair will try and (hopefully) resolve the issue.
Method 3: Delete and re-add the Wireless Network
1. In “Network and Sharing Centre,” select “Manage wireless networks”.
2. Right click on your wireless network and choose “Remove network” from the drop down list.
3. Return to “Network and Sharing Centre” and click on “Connect to a network.” Select your network from the list.
Method 4: Alter Power Management profile
1. If this issue occurs after resuming from hibernate or sleep mode, or are having intermittent connectivity issues, adjust your Power Management profile to set your Wireless Adapter Settings to Maximum Performance.
2. Navigate to “Start -> Control Panel -> Hardware and Sound -> Power Options -> Change plan Settings”
Note: This example is where the laptop uses Power saver, but this method can apply to the other plan settings (Balanced and High Performance).
3. Select “Change advanced power settings.”
4. Scroll down to “Wireless Adapter Settings” and change both configurations (battery or plugged in) to “Maximum Performance.” If you prefer, you can do this for all of your power profiles. Click “OK “to finalise changes.
Method 5: Check settings on your wireless router
1. In the “Network and Sharing Centre “select “Change Adaptor settings.” Right click on the network device you use to connect to the internet and select “Status.” The Wireless Network Connection Settings dialog box comes up. Select the “Details”button.
2. The Network Connection Details dialog box appears. Note down the “IPv4 default address”.
Note: The above points may not be possible if you are unable to connect to the wireless network at all. In which case if you know the IP address of your router then utilise it for the next points or else try 10.1.1.1, 192.168.0.1, 192.168.1.1, 192.168.2.1. Alternatively you could use another computer or laptop on which the internet connection is working properly to check these details.
3. Navigate to an internet browser and enter in the relevant IPv4 address into the browser bar.
5. Browse through all the settings and check that the router is set to broadcast it’s network name (SSID), ensure that you are connecting to the correct wireless network (SSID) and that you are using the right WEP/WPA/WPA2 passkey on both devices. We advise to use ‘Windows Connect Now’ or ‘Wi-Fi Protected Setup’ (if available) on your wireless router to ensure that the connection is setup correctly. The example below shows the correct wireless settings on a Netgear DGND3700 wireless router.
6. If you are trying to use WPA or WPA2, ensure that both your network adapter and wireless router support this protocol. If you are having issues detecting your wireless network when using WPA or WPA2, try configuring your router to use WEP instead and see if you can connect. If you can only connect to the internet via WEP, then your networking hardware may require a firmware upgrade. If you are unfamiliar or unsure about updating your firmware, we suggest contacting your hardware/router manufacturer for advice on the matter.
Note: The change between WEP/WPA/WPA2 will need to be performed on both your wireless router and computer(s).
7. Once you have reviewed the wireless router settings and made changes (if required), logout of the router. Turn the wireless router off and on again for changes to take effect.
Method 6: Reinstall Network Adaptor Driver
1. Click “Start” and type “Device Manager” into the search bar. Click on Device Manager to open it.
2. Navigate to Network Adaptors, right click the Wireless Network device and select “un-install.”
3. A warning message will appear requesting confirmation that you want to uninstall the Wireless Network device. Click “OK “to continue.
4. Exit out of Device Manager and reboot the laptop/PC.
5. Upon startup, a message will pop stating that new hardware has been found and installed. A pop-up window will then appear advising “One or more wireless networks detected, click here for more options”. The “Available Wireless Networks” window appears that lists all networks in range. Select desired Access Point to connect to then once connected, test trying to access the internet.
Method 7: Reset TCP/IP stack
1. One of the main Windows components of your internet connection is the TCP/IP stack which can become corrupt or damaged in some cases. Resetting the TCP/IP stack using the Netshell utility (Netsh) may resolve the problem.
3. Type in the following commands:
netsh int ip reset reset.log
4. Restart your computer and try to connect to the internet.
If all else fails, post a comment below or contact your modem/router provider or ISP for further assistance.